The Radiator Cover Megapost
December 22, 2019
Welcome to the Radiator Cover Megapost combining the 5 or 6 posts about the cover made for the dining room radiator in '18 - '19.
Winter came early this year!
Made at 173: Simple Toolboxes
December 2, 2019
As you probably know, I like finding things to do with scrap wood after a project. In this case, I've made a few simple toolboxes, and if you read through, you'll practically get a tutorial! The first was after the back porch remodel in 2011, and was just a decorative piece for the back porch...
It's painted Valspar's Golderod in semi-gloss, and just so you know - that's going to come up again in a little while. I also lightly distressed it, and used Valspar's antiquing glaze to give it a bit of an aged look. The second one I made maybe around 2013, was a toolbox for the workshop.
Most of the time I haul tools around in a 5 gallon bucket with one of those organizers, but sometimes it's nice to just throw a few tools in a box and head out...
Like the first toolbox, this one is of simple design, but I did make one seemingly goofy little addition. I added a little magnetic cupboard door catch that I salvaged when I changed some of the kitchen cabinets. I use this to hold some drill screwdriver bits. Aside from that - simple! The only other thing really different with this one (aside from no antiquing, etc.) was this toolbox is much larger, a full 30 inches long.
This time I made one to be used as a delivery vehicle for a Christmas present. And this is where the bit of tutorial comes into play. As is my wont, I started with a piece of scrap wood, this one left over from the dining room built-in project...
Then I laid out the dimensions of the end boards, using a compass so I could set the proper angle on the miter saw. Quite honestly, this was a wasted step! All I really needed to do was mark the center of the top of the board and cut from that point to where the horizontal line meets the edge of the board! So much simpler!
After that, I clamped the two end pieces together and sanded the edges to make sure they were symmetrical. If you look closely you'll spy a couple other things. First, that 's 5/8" dowel that I used for the handle. After I drilled the holes for the handle, I used the dowel to make sure the end pieces were lined up correctly for edge sanding. The other thing, on the left of the picture you can see one of the two side boards, both of which were cut from another scrap piece.
And here's the dry fit. Please notice the pencil marks - good thing I didn't go with my near slide-rule measurements!
Then I used my corner clamp, which I've used for several projects now with great success, to make sure the corners were at 90 degrees, and glued them together...
Ha! See that bullseye on the side, that board was originally going to be part of the 45-degree marking tool I made a week or so ago. And here's the dry fit with the handle in place...
Craftsman was the tool of choice for my dad when I was a kid, then they went into decline for a number of years, but I'm so happy to say they're making a great comeback of late! Anyway, here's a beauty shot of my air finish nailer, that's worked well for me since probably 2000 or 2001. Obviously, I used finish nails to complement the glue and give the toolbox some added, more permanent strength...
Then it was Thanksgiving Day, and the workshop sat still and felt a bit lonely...
After installing the bottom of the toolbox with yet another piece of scrap wood, I gave the toolbox two coats of Valspar's Goldenrod (told ya that was gonna come up again)...
Then it was time to distress it a little. It's always a difficult step, to take a newly built, freshly painted project and beat it up. So, over the years whenever I came across a little length of chain, I've saved it (don't make this weird) and you can see the little collection to the right of the hammers...
From that collection, I chose an old one with a but of rust and grime and gave the toolbox a few well-aimed whacks.
Then I strategically sanded the toolbox back down to the bare wood at key points of the edges, imagining where there would have been some natural wear and tear. Then dad's old ball-peen hammer gave it a few little divots.
Then I used a little (very little, I'm conserving my favorite glaze - which has been discontinued) Valspar glaze...
And just like that, it was finished!
These toolboxes aren't only useful, they're quick, fun little projects. I'm considering making a more sophisticated one just for fun - we'll see!
Subscribe to:
Posts (Atom)
Social Icons